Reliable Heating & Cooling Services in Tomahawk

Completed prepaid annual maintenance on residential furnace system. Performed comprehensive inspection of all components including blower assembly, electrical connections, and system controls. Verified proper operation of squirrel cage blower motor and checked wire connections for secure attachment. Utilized diagnostic equipment to measure system performance parameters and confirm unit is operating within manufacturer specifications. All components found in satisfactory condition with no immediate repairs required. Provided customer with estimate for air quality improvement equipment to enhance indoor air quality.

Completed annual prepaid preventive maintenance inspection on AC/mini split system. Performed comprehensive system evaluation including blower motor assembly, electrical connections, and air handler components. All components found operating within normal parameters with no deficiencies noted or repairs required at this time.

Performed seasonal boiler shutdown per customer request. Closed both water makeup valves to isolate the system from the water supply, shut off the gas supply valve to secure fuel source, and turned off the local power switch to de-energize the unit. Boiler is now secured for the summer season and ready for reactivation when heating is required.

Responded to no cooling complaint on residential AC unit experiencing freeze-up conditions. Performed comprehensive system evaluation and confirmed unit was low on refrigerant charge. Conducted thorough leak test to identify source of refrigerant loss per industry protocols.

Completed Partner Plan annual heat inspection on furnace system. During inspection, identified flame sensor with dead spot requiring attention, igniter showing mild corrosion, and inducer motor capacitor reading below optimal specifications. Documented all findings with photos of blower motor assembly and burner manifold components. Provided estimates for necessary repairs to ensure reliable system operation through heating season.

Responded to no cooling complaint on older R-22 system. Upon arrival, performed diagnostic evaluation to determine operational status and cooling capacity. Unit confirmed not cooling properly. Due to age of equipment, obsolete R-22 refrigerant, and current system condition, recommended comfort advisor consultation for replacement options.

Completed annual heat inspection and preventive maintenance on 11-year-old furnace as part of prepaid partner plan. Accessed unit through floor opening, inspected ventilation components including fan housing and louvers in attic space, verified proper airflow and operational status. All PM options reviewed and system found operating within normal parameters.

Completed replacement of burner assembly, inducer motor, and ignitor on heating unit as per approved estimate. All components installed, system tested and verified operational with proper ignition sequence and combustion. Unit returned to service with all safety controls functioning correctly.

# HVAC Inducer Motor Replacement Replaced defective inducer motor on heating system per approved estimate. Removed old motor assembly, installed new inducer motor, and verified proper operation. Unit tested and confirmed functioning correctly with no issues noted upon completion.

Completed annual Partner Plan inspection on 4-year-old boiler system. Performed comprehensive heat inspection of all major components, including heat exchanger, burner assembly, and associated piping. Documentation captured showing heat exchanger with visible rust and corrosion on fin tubes, corroded connection fittings, and moisture-related deterioration. System currently operational with no immediate service requirements identified at this time.

Responded to no cooling complaint on 8-year-old residential air conditioning system. Upon arrival, contacted property owner and gained access to perform diagnostic evaluation. Inspected outdoor condensing unit and identified failed dual run capacitor exhibiting severe corrosion and deterioration. Removed defective capacitor from electrical control panel and installed new replacement capacitor with proper microfarad ratings. Verified all electrical connections were secure, tested system operation, and confirmed unit returned to normal cooling function.

Completed Partner Plan annual maintenance inspection on boiler system. Found combustion levels outside of manufacturer specifications and performed necessary adjustments to bring all readings back within proper parameters. Verified system operation and documented equipment condition with photos showing heat exchanger assembly and pressure measurements using calibrated digital manometer reading -04.67 inches of water column.

Responded to callback for recently installed boiler exhibiting leakage beneath unit. Upon inspection, identified seepage at packing nuts on new brass ball valves in supply piping system. Tightened packing nuts on affected valves to eliminate leaks and restore proper seal integrity. Verified no further seepage present after adjustment.

Completed annual preventative maintenance inspection on furnace system. Performed comprehensive system evaluation including visual inspection of all accessible components, ductwork, and ventilation systems. All equipment found operating within normal parameters with standard dust accumulation noted on mechanical components.

Completed annual prepaid maintenance inspection on boiler system. Upon inspection, discovered heat exchanger failure with extensive rust and corrosion throughout the finned coil assembly, compromising system integrity and safety. Documented equipment condition with photographs showing deteriorated heat exchanger fins with heavy oxidation and pressure gauge reading approximately 15 PSI. Informed customer of failed component requiring repair or replacement to restore safe operation.

Completed annual preventive maintenance on 15-year-old Furnace system. Performed comprehensive inspection of blower assembly and verified proper operation. Conducted combustion analysis with readings showing O2 at 9.8%, CO2 at 6.3%, and ambient CO levels at 44 ppm, all within acceptable parameters for safe operation.

Completed annual preventive maintenance inspection on boiler system. Verified system pressure readings, inspected all mechanical connections and copper piping, and documented equipment condition with photographs for service records.

Responded to no heat call on 20-year-old furnace unit. Upon inspection, identified multiple critical component failures including corroded burners, igniter, and flame sensor. Inducer motor found drawing amperage higher than rated specifications, and inducer capacitor tested out of spec. Documented all failing components with photographs showing extensive corrosion on burner assembly and deteriorated condition of internal components. Due to age of unit and extent of required repairs, provided estimates for necessary work and scheduled comfort advisor consultation for system replacement evaluation.

Completed annual furnace inspection on Goodman GM9S060B12DH11J 62,000 BTU/Hr Category IV direct vent unit. Identified aging inducer motor and rust formation on burners requiring attention. Provided customer with immediate repair and preventive maintenance recommendations to address deteriorating components before potential system failure.

Completed annual heat inspection on 12-year-old furnace as part of Partner Plan maintenance agreement. Performed preventive maintenance procedures, inspected blower assembly and internal components, and documented system condition with photos. Customer will need 20x25x5 filter replacement scheduled for next visit.