Heating, Cooling & Air Quality Services in Lake Tomahawk

Completed Partner Plan inspection of furnace per customer complaint of dripping sounds and light issues occurring when units are not in use. Inspection revealed UV bulb nearing end of service life and active water leak identified at bottom left side of inducer assembly. Documented findings with photos and provided estimates for necessary repairs.

Completed annual partner plan preventive maintenance inspection on air conditioning system. Performed comprehensive system evaluation including airflow assessment, static pressure measurements, and temperature differential analysis. Documented control board operation with digital display functioning properly, verified proper wire connections and labeling throughout system, and confirmed all electrical components securely mounted. All inspection checklist items evaluated with system operating within normal parameters and no deficiencies identified at this time.

Completed Partner Plan annual maintenance inspection on furnace system. During inspection, identified mild corrosion on the igniter assembly with heat-related discoloration visible on mounting bracket and surrounding components. Documented condition with photos showing affected igniter assembly and burner components. Provided estimate for igniter replacement to prevent potential failure during heating season.

Responded to mini-split system not operational following previous rodent and lightning damage. Contacted technical support to verify warranty coverage and received authorization to proceed with diagnostics. Upon inspection, identified broken communication wire on control board and failed air flow monitor (AFM). Completed repairs under warranty coverage, replacing damaged communication wire and AFM unit. System restored to proper operation and tested for functionality.

Completed annual inspection on mini split system per customer request due to history of animal intrusion into units over the past three years. Thoroughly inspected all interior and exterior components, electrical connections, contactors, and control panel wiring for signs of damage, nesting materials, or compromised connections. System found to be clean and free of debris with no evidence of animal activity; all electrical components, wiring, and connections verified secure and operational, clearing unit for safe operation.

Completed annual preventive maintenance inspection on 10-year-old furnace as part of Partner Plan agreement. Performed comprehensive system evaluation, inspected burner assembly through observation port, verified proper operation of all components, and examined ductwork and ventilation system. All equipment found operating within normal parameters with no immediate service needs identified.

Responded to service call for excessive noise during boiler operation with indirect water heater. Diagnosed failing blower motor bearings causing severe vibration that damaged mounting grommets and likely compromised the blower wheel integrity. Documented equipment condition with photos showing deteriorated motor assembly and damaged mounting components. Provided written estimates for repair options and recommended comfort advisor consultation for comprehensive system evaluation.

Completed Partner Plan annual inspection on air conditioning unit. Observed slight buildup of dust and pollen on condenser coil along with leaf and acorn debris inside condenser cabinet. Cleaned condenser coil with water hose, wiped down interior base pan, and removed all debris to ensure proper airflow and system efficiency.

Completed preventive maintenance tune-up on 3-year-old furnace system. Inspected and verified proper air filter installation, confirmed blower wheel assembly operation with normal dust accumulation present, and performed standard annual maintenance checks to ensure system efficiency and safe operation.

Performed annual inspection on 24-year-old cabin heater (second unit on property). Observed significant corrosion on pilot assembly and burner, with flame pattern indicating proper combustion during testing. Advised customer that while system is operational, replacement of pilot assembly is recommended, though burner component is obsolete.

Performed annual furnace maintenance as part of scheduled tune-up service. Identified significant igniter corrosion on the metal assembly and substantial mineral buildup on the humidifier pad/filter element. Both degraded components were replaced to restore proper system operation and efficiency.

Performed boiler flush procedure to address low hot water flow issue. Diagnosed plugged plate heat exchanger. Successfully restored system functionality by flushing plate-to-plate heat exchanger with appropriate cleaning solution to remove mineral deposits and restore proper circulation.

Completed annual tune-up inspection on residential furnace system. Inspected heat exchanger, burners, and gas valve assembly with no issues detected. Checked and cleaned condensate drain components to ensure proper drainage and prevent potential water damage.

Completed duct cleaning service addressing significant dust accumulation and debris in the trunk lines and return duct. Inspection revealed wooden duct surfaces with visible water damage and discoloration on the upper surfaces. Thoroughly cleaned all accessible trunk lines, removing built-up dust and contaminants to improve system efficiency and air quality.

Returned to site to address warranty issue. Performed combustion analysis using Kicker C161 analyzer, which indicated O2 at 5.1%, CO2 at 10.5%, and temperature at 101.9°F. Replaced faulty LP regulator to restore proper system operation.

Responded to no-heat call for 1.5-year-old furnace showing error code E223 (pressure switch stuck open). Diagnosed restriction in exhaust vent, which was frozen shut due to snow accumulation around PVC exhaust termination. Cleared ice blockage from vent pipe, allowing proper venting and resolving the pressure switch fault. System now operating normally.

Responded to emergency no-heat call for 3-year-old boiler system showing ignition lockout failure. Diagnostic testing confirmed combustion issues related to frozen LP regulator. Restored heat functionality with thermostat now reading 52°F, up from critical low of 32°F.

Conducted annual Partner Plan heat inspection on furnace. Found significant accumulation on blower wheel requiring maintenance. Presented customer with the pull and clean option to restore optimal system performance. Filter showed severe dirt buildup and deterioration that may be restricting airflow.

Performed annual heat inspection under Partner Plan maintenance agreement. Identified high resistance on flame sensor, corrosion affecting burners and igniter, and significant dust accumulation in ductwork. Cleaned accessible components and provided customer with remediation options for remaining issues.

Responded to service call for non-functioning split system heat. Determined the existing AC unit is not designed to operate efficiently at current low temperatures, which is causing the heating failure. Inspected system components through access panel and documented condition of refrigerant lines and insulation. Recommended installation of either a gas/electric heat source or cold climate heat pump to provide reliable heating for the property.